An open-source cooling cap for engine rooms, bakeries, and other hot places people work

Bright Meadow Group | Observe · Design · Intervene


Anyone who has stood a watch in a ship’s main space knows the heat. The air feels thick enough to lean on. The deck plates radiate through your boot soles. Every pipe, casing and exhaust trunk throws heat at your face like an open oven door. You crawl into the bilge to check a strainer, and by the time you climb out, your coveralls are soaked and your hat is wringing wet.

Heat changes how maintenance gets done. A job that takes forty careful minutes in a cool shop gets done in fifteen hurried ones in a space at 110°F. A torque check gets skipped. A gasket gets reused. A log entry gets written from memory. In the Navy, military discipline and inspection pressure push back against that. In civilian shipping and industry, with lighter oversight and a business that may decide a task can wait, the heat wins more often. A steering gear, a fuel pump or a boiler control is only as reliable as the person who maintained it on the hottest day of the year.

We need regulation, and we need ventilation, insulation and work/rest schedules that the people who control those spaces actually enforce. We also need the jobs to be doable. This piece lays out one tool toward that: a soft cap that moves heat off the head through a full shift. It costs little to make, and it’s released openly for anyone to build.


OBSERVE

What’s on the market

Look for cooling headwear today and you’ll find three kinds of product.

Evaporative caps. Soak them in water, wring them out, and wear them. They’re cheap, around $7–10, and they work outdoors in dry air. Distributors warn that in humid buildings, the water won’t evaporate well. They’re also polyester, and polyester melts. On a head near fuel and hot steel, a melting cap is a liability.

Freezer and phase-change packs. Hard hat inserts, neck wraps and vests hold packs at 58–64°F. They work without airflow, which suits indoor spaces, and they do cool. They’re also cold enough to be uncomfortable against skin, they need a freezer or ice chest, and a vest with packs can weigh six to nine pounds. Gear that feels like ice on your forehead ends up in a locker, and a cooling device left in a locker cools nobody.

Aluminized hoods. Foundries and steel mills use full hoods of aluminized aramid to turn back radiant heat. They protect well and run hundreds of dollars, some well past a thousand. They’re built for pouring molten metal and are too much hat for turning a valve in a pump room.

Under the cheap end of that list sit the hard hat liners stuffed with cooling rags, and plain cotton caps that soak up sweat and hold it against the scalp like a wet towel on a radiator.

The physics underneath

Heat leaves a head three ways:

  1. Into cooler air. This only works when the room is cooler than the skin, about 93°F.
  2. Into evaporating sweat. Each gram of sweat that evaporates carries away about 2,400 joules. This works even in hot rooms, as long as the air can take more moisture.
  3. Into a sink. Anything cooler than the skin that can soak up heat: a cold pack, a block of wax, a reservoir of water.

When the room is hotter than the skin, the first route runs backward and the room heats the head. That leaves sweat and sinks. Engine rooms, bakeries, laundries and foundries are hot, and many of them are humid, so sweat struggles to evaporate.

That points to a quiet loss in ordinary headwear. A cap that soaks up sweat and holds it throws away cooling the body already paid for. At 10 grams of sweat an hour from the head, a 12-hour shift produces about 120 grams. Evaporated, that’s roughly 290,000 joules of heat leaving the body. Soaked into a hatband, it’s a wet hat.

The opening

No product we found combines these four things in a soft cap built for hot, humid indoor work:

  • A reflective outer shell against radiant heat.
  • A way to keep sweat evaporating in humid air.
  • Flame-resistant materials throughout.
  • Comfort that lasts a full shift.

That gap is the design brief.


DESIGN

The brief

  • A soft cap shaped like a chef’s or sailor’s cap: a puffed crown over a fitted band.
  • It moves heat off the scalp steadily for up to 12 hours.
  • It never chills the scalp below comfortable. Nothing frozen.
  • The outer surface stays safe to grab.
  • Flame-resistant materials, soft against skin, washable where it touches the body.
  • Simple enough to cut and sew in an ordinary apparel shop.

The shape

The cap works like a small building: a foundation, walls and a roof. The band is the foundation, sitting at the hatband line across the forehead, over the tops of the ears and around the back of the skull. The puffed crown is the roof, standing off the head with air beneath it. Where the crown’s overhang meets its sidewall, just above the band, sits the working part of the cap.

That shape does several jobs for free. The puff creates an air gap over the head without any added material. The overhang shades a strip of the crown wall the way an eave shades a soffit vent. The band gives a firm ring to anchor closures, cooling hardpoints and the sweatband.

How it moves heat

The cap uses the second and third routes together. The wick and sweatband pull liquid sweat off the skin and out of the eyes, and the sweat evaporates off the fabric. A ring of silica gel packets at the crown seam then soaks up that vapor.

Silica gel works like a sponge for water vapor. It keeps the air inside the crown dry, so sweat keeps evaporating off the scalp even in a humid room. When silica soaks up vapor, it gives off about the same heat the sweat took from the skin. So the silica sits outside a heat shield, and its heat leaves through the outer shell into the room.

In effect, the cap works as a small pump for water vapor. Sweat leaves the skin, the heat it carries is dumped outside the shield, and the head stays cooler.

Why the silica sits at the crown seam

We first tried the silica in the band. The numbers ruled it out.

Silica in the bandSilica at the crown seam with a spreader
Surface shedding the heat~0.026 m²~0.06 m²
How much hotter than the room it runs (still air)~50°F~22°F
Insulation between silica and scalpabout 3 mmair gap, membrane, reflector, second air gap
Heat leaking back to the head~7 W of the 7.5 W released~2.5–3 W
Net coolingclose to zeroabout 4.5–5 W

In the band, the silica’s heat had nowhere to go but back into the forehead. At the crown seam, it has more surface to shed from and room for a real shield. A thin heat-spreader laminate behind the packets carries their heat up across the crown top, so the whole roof sheds it.

The stack

Band (chassis)

  • Sweatband: thick flame-resistant terry in modal/aramid, 4.5 cm tall. Attached with FR hook-and-loop so it comes out for washing.
  • Band body: FR webbing over a thin FR felt stiffener.
  • Hardpoint sleeves: at the forehead, both temples, and the base of the skull. They ship empty, ready for future modules.
  • Top edge: open mesh, so vapor can rise into the crown.
  • Closure: split rear tails on either side of the base-of-skull hardpoint. FR hook-and-loop is standard, with tie and buckle versions. All metal stays outside, away from skin.
  • Sizes: SizeBand circumferenceS54–55 cmM56–57 cmL58–59 cmXL60–62 cm The closure adjusts about 2 cm either way.

Wick

An FR modal liner covers the band and continues up into the crown. It ends a few millimeters short of the packet sleeve and never touches the packets. Wet fabric pressed against silica floods the beads with liquid, and they fill faster that way than they do on vapor.

Seam ring, inside to outside

  1. Wick fabric
  2. Spacer-mesh air gap
  3. ePTFE membrane, which lets vapor through and stops liquid sweat
  4. Perforated aluminized reflector, which blocks radiant heat from the warm packets while vapor passes through the holes
  5. Spacer-mesh air gap. The reflector only works with air on both sides.
  6. Packet sleeve with a mesh inner wall
  7. Silica packets
  8. Heat-spreader laminate running up across the crown top
  9. Aluminized FR outer shell, vapor-tight so room humidity can’t reach the silica

Crown top, inside to outside

  1. FR modal lining resting lightly on the head
  2. A 10–15 mm air gap held open by FR silicone foam standoffs
  3. 5 mm aramid felt with a perforated aluminized face pointing down at the head
  4. Spreader laminate
  5. Aluminized FR shell

Packets

  • Six to eight packets of 20–25 g each, about 150 g per set.
  • Type A silica beads, 2–4 mm, with about 10% cobalt-free orange-to-green indicator beads behind a small window in the shell.
  • Pouches of aramid mesh, which survive repeated oven drying.
  • Workers swap packets from outside through slits along the seam, closed with FR hook-and-loop flaps. The hat stays on the head.
  • One set holds about 30 g of water, roughly three hours at 10 g of sweat an hour. Four sets cover a 12-hour shift.
  • Spent packets dry out in two to three hours at 250°F and go back into service.

Two crowns, one band

  • Sealed silica crown: for humid spaces such as engine rooms, bakeries, laundries and kitchens.
  • Vented crown: no packets. Mesh vents in the shaded strip under the overhang and a covered button vent on top, for dry, ventilated spaces where sweat evaporates on its own.

Comfort

Nothing frozen. Cold packs pull heat fast, but a forehead pressed against a 32°F pack wants the hat off within minutes. This cap relies on evaporation and silica, so the scalp can’t drop much below the temperature of the air under the crown. The pull stays steady and gentle across a shift.

Soft against skin. Everything touching skin is FR modal or a modal/aramid blend: smooth, cool to the touch, quick to wick, and it chars instead of melting. Fine merino wool is an alternative for those who prefer it. The construction avoids:

  • Polyester and nylon against skin
  • Leather, which stiffens and mildews in wet heat
  • Nickel-plated hardware against skin
  • A seam across the forehead
  • Tags

Silver-treated yarn in the liner helps with odor over long shifts. The sweatband and liner come out and go in the wash.

Safe to grab. In a 105°F room with still air, the crown surface runs about 125–130°F, about the outside of a coffee mug. Any air movement lowers it. No metal sits on the outside to concentrate heat.

Targets for the bench

MeasureTarget
Net heat removed from the head, humid space4.5–5 W, steady
Hours per packet set~3
Lowest scalp temperatureskin temperature or above, never cold
Crown surface, 105°F still air~125–130°F
Weight with packets~260 g (a hard hat runs about 400 g)

When the packets are spent, the cap still works as an insulated, reflective sweatband that keeps sweat out of the eyes. A spent cap leaves the wearer no worse off than an ordinary hat.

A steady 4.5 watts sounds small, so here’s the arithmetic. Over 12 hours, 4.5 W comes to about 194,000 joules. That’s the cooling the body would otherwise have to buy by sweating out roughly 80 more grams of water, close to three ounces from the head alone, in air too humid to evaporate it.


INTERVENE

Prove it on the bench

Before anyone sells this cap, it gets measured. The rig is a heated, sweating headform: a head-shaped form held at 93°F, with porous skin fed water at a controlled rate. Run it 12 hours in three conditions:

  1. 105°F air at high humidity
  2. The same air with a radiant heat source from one side
  3. Dry, ventilated air

Log the heater power, the grams of water the packets absorb, the temperature at the seam ring and the crown top, and the temperature just inside the shield. Run a plain cotton cap and the vented crown alongside for comparison.

If the heat leaking back through the shield runs higher than the estimate, add thickness to the felt or the air gap before changing anything else. Marketing claims stay inside what the bench shows: watts removed and hours per packet set. Claims about preventing heat illness require whole-body testing on people, and that’s a separate study.

Certify the fabric

The full fabric stack goes out for flame-resistance testing before any FR claim appears on a label. The components are chosen to pass, and a lab report is what proves it.

What it costs to make

Rough figures at 100,000 hats a year, to be confirmed with supplier quotes:

ItemCost (overseas cut-and-sew)Cost (US cut-and-sew)Suggested list price
Hat$16–26$23–36$69–89 (overseas) / $95–120 (US)
Packet set (one 3-hour charge)$3–5—$15–19
Shift kit (four sets)$12–20—$55–65

For comparison:

  • FR knit caps list from about $14 to $38.
  • An FR phase-change cooling vest without packs runs roughly $72 to $175.

The silica is the cheap part. Bulk Type A beads cost around $2 per kilogram, so the silica in one set runs well under a dollar. The fabric and the sewing set the price.

Replacement packets will likely earn more over time than the hats, the way filters do for respirators. A builder who wants to keep prices low for working people can sell packets close to cost and still run a healthy business on volume.

The release

This design is released openly. Anyone can build it, sell it, improve it, or adapt it for their trade, without permission and without paying royalties. A shipyard’s sewing loft can make them for its crews. A bakers’ union can contract a run for its members. A safety supplier can put them in a catalog. A machinist in Manila or a cook in Mumbai can build one at a kitchen table from the stack listed above.

The reason is simple. Heat sits on working people in engine rooms, bakeries, laundries, foundries, kitchens, mines and greenhouses all over the world. A patent would slow this cap down and raise its price for the people who need it most. Technology should benefit the people doing the work.

We ask one thing of anyone who builds it: publish your bench numbers. If you find a better sorbent, a lighter shield or a smarter spreader, share it so the next builder starts from your results.

Who carries what

A cooling cap is personal protective equipment, the last line of defense after the engineering is done. It doesn’t replace ventilation, insulation on hot equipment, exposure limits or work/rest schedules, and it doesn’t excuse skipping them.

Where caps are used, the employer supplies them, keeps spare packets and sweatbands on hand, provides a place to dry packets, and gives crews paid time to cool down and swap. The responsibility for the space stays with the people who control it. The cap makes the work more bearable while they do their part.

The ask

To safety engineers and university labs: build the rig and test the numbers.

To unions and crew organizations: put a few dozen caps on your members and tell us what they say after a summer.

To apparel shops and safety suppliers: the pattern is yours.

To shipowners, bakery operators and plant managers: buy them for your people, and fix the ventilation while you’re at it.

It looks like a tinfoil hat, and crews are going to call it one, so that’s the name.


Specification summary (for builders)

  • Band: FR modal/aramid terry sweatband (removable). FR webbing over FR felt stiffener. Four hardpoint sleeves. Open mesh top edge. Rear split closure. Sizes S–XL.
  • Wick: FR modal liner from the band into the crown, ending short of the packet sleeve.
  • Seam ring (inside to outside): wick, spacer gap, ePTFE membrane, perforated aluminized reflector, spacer gap, mesh-walled packet sleeve, silica packets, spreader laminate, aluminized FR shell.
  • Crown top (inside to outside): FR modal lining, 10–15 mm standoff air gap, 5 mm aramid felt with downward perforated reflective face, spreader laminate, aluminized FR shell.
  • Packets: 6–8 × 20–25 g Type A silica (2–4 mm), ~10% cobalt-free indicator beads, aramid mesh pouches. Regenerate at 250°F for 2–3 hours.
  • Crown options: sealed silica crown (humid spaces) or vented crown (dry spaces).
  • Bench protocol: sweating headform at 93°F; 105°F humid, radiant, and dry runs; 12 hours; log heater power, water absorbed, seam and crown temperatures, and shield temperature.

Sources

Spread the love

Related Posts